Low Profile VESA Mount Kit User Guide
Overview
The Extron® Low Profile VESA® Mount Kit (LPVM-1) allows
monitors or Extron touch panels to be wall mounted to a two-gang
UL-certified junction box, a two-gang mud ring, or directly onto
any solid surface, such as brick, wood, masonry, or drywall. The kit
supports both the B-type (20 x 50 mm) and D-type (75 x 75 mm)
VESA mounting patterns. The monitor attaches to the wall at a fixed
angle with no tilting.
Tongue
Holes to Secure
Plate 1 to Wall
Bottom Tabs (2)
Holes to Secure
Plate 1 to Mud Ring
or Junction Box
CAUTION: The maximum loads for the LPVM-1 are:
VESA B — 4.4 pounds (2 kg)
VESA D — 30.8 pounds (14 kg) if the LPVM-1 is
mounted directly to the wall, not a mud ring.
Extron LPVM-1
Plate 1
The kit consists of two separate steel plates, held together by two
locking screws. Plate 1, which attaches to the wall, has a protruding
tongue at the top. The tongue fits into a groove at the top of plate
2, which attaches to the back of the display device (see the figure at
right).
Groove
B-Type VESA
Mount Holes
D-Type VESA
Mount Holes
Optional Tools and Equipment
Locking Screws
(#10-32 Phillips)
To mount the LPVM-1, you may need some or all of the following
items that are not provided by Extron:
Bottom Edge
•
•
•
•
•
•
Mud ring or UL-certified junction box
Tools for cutting a hole in drywall
Conduit or surface raceway
Extron LPVM-1
Plate 2
Power drill with a bit that is appropriate for the wall type
Screwdriver
Four screws or bolts, to attach the LPVM-1 to the wall (these must be appropriate for the type of wall).
Installation Instructions
To VESA mount a touch panel or monitor using the LPVM-1, follow these instructions:
3
Disassembling the LPVM-1
1. Use a Phillips screwdriver to loosen the two locking screws until the two plates of the
LPVM-1 can separate.
2. Swing the bottom tabs of plate 1 away from the bottom edge of plate 2.
3. Pull plate 1 down to remove the tongue from the groove in plate 2.
1
4. Select a suitable mounting site and decide whether the LPVM-1 will be mounted directly
to the wall (see below), or to a mud ring or UL-certified junction box (see the next page).
2
Mounting the LPVM-1 Directly to a Wall:
a. If the LPVM-1 is being mounted directly to drywall, you may cut a
hole in the drywall that is 2.5 x 2.5 inches (6.35 x 6.35 cm) to run
cables inside the wall cavity. If the LPVM-1 is attached to a solid wall
or you do not want to run cables through the drywall cavity, the
cables should be enclosed in conduit or raceway.
4b
4c
b. Use plate 1 to mark the position of the four holes in the wall and
drill four holes, using a drill bit that is appropriate for the wall type.
Plate 1 accommodates screws up to 1/4 inch in diameter.
Screws (4)
Appropriate
to Wall Type
c. Secure plate 1 to the wall with four screws or bolts that are
appropriate for the wall type. Ensure the tongue is facing up.
|
Elation Professional Work Light 60TM User Manual
Excalibur electronic Motorized Toy Car PR11BK 2 User Manual
FEIN Power Tools Drill ASKEU 636 Kin User Manual
Fisher VCR FVH T619 User Manual
FujiFilm Camera Lens 2030526 User Manual
GE Air Conditioner AEV24DK User Manual
GE Microwave Oven JE1160 User Manual
GE Oven PT916BM User Manual
GE Ventilation Hood JN322 User Manual
GN Netcom Headphones STRATUS ULTRA G User Manual