Verilux Indoor Furnishings PL04 User Manual

®
Planet Light  
PL04  
Energy Saving Natural Spectrum®  
Floor Lamp  
 
IMPORTANT SAFETY INSTRUCTIONS  
SAVE THESE INSTRUCTIONS  
Thank you for purchasing the Planet Light® Energy Saving Natural  
Spectrum® Floor Lamp. Please read the following safety information  
before using. To reduce the risk of fire, electrical shock or injury to  
persons:  
• Do NOT dismantle.  
• Do NOT alter power cord.  
Turn off/unplug and allow to cool before replacing bulb or cleaning.  
GENERAL PRECAUTIONS  
• For indoor use only.  
• The lamp is an electrical device. DO NOT USE NEAR WATER.  
• Before plugging in the lamp, check to make sure the voltage of the  
wall socket does not exceed 120 volts.  
• Not for use with light dimmers, timers, motion detectors or extension  
cords.  
• This product may cause interference with radios, cordless  
telephones or devices that use a wireless remote control, such as  
televisions. If interference occurs, move the product away from the  
device, plug the product or device into a different outlet or move the  
lamp out of the line of sight of the remote control receiver.  
• Unplug from electrical outlet for extended periods of non-use or  
during lightning storms to ensure protection of the electronics.  
WARNING: Do NOT use lubricating agent in assembly; please see  
troubleshooting section if you are having difficulty assembling your  
lamp.  
WARNING: Do not use the lamp outside or in wet locations such as  
bathrooms. It is intended for indoor, dry use only.  
WARNING: This product contains Mercury in the bulb. Dispose of  
bulb per local regulations.  
3
 
GETTING STARTED  
Main Parts & Controls  
F. Polarized Plug  
G. Bulb  
H. On/Off Switch  
A. Lamp Head  
B. Gooseneck  
C. Shaft  
D. Lamp Base  
E. Power Cord  
Close-up of Lamp Head  
A
B
G
H
C
E
D
F
CAUTION:  
DO NOT LIFT THE LAMP BY THE GOOSENECK. THE LAMP SHOULD  
BE LIFTED BY THE SHAFT.  
4
 
UNPACKING YOUR LAMP  
1. Remove all pieces from box. Locate 2 Phillips head screws.  
2. Detach red plastic pieces and store them in the event you need to  
return the lamp.  
3. Important: To avoid scratching the metal shaft, do not use a sharp  
object to cut the plastic covering. The clear plastic covering on the  
shaft is specially designed to tear away easily.  
IMPORTANT NOTE:  
Remove red plastic protective pieces prior to assembly.  
5
 
ASSEMBLY INSTRUCTIONS  
Read Instructions Carefully Before  
Assembly:  
1. Connect the two ends of the Power  
Cord (between the Base and the  
Shaft) using the lock connectors.  
2. Carefully tuck excess Power  
Cord into the Shaft. DO NOT  
CUT OR SHORTEN THE POWER  
CORD.  
3. Insert the Flex Pole and the Shaft  
into the Base.  
4. Check direction of the lamp and  
the hole on the Base, then use  
a Philips Head Screwdriver (not  
included) to tighten the screw into  
the hole. CAUTION: BE VERY  
CAREFUL NOT TO PINCH ANY  
PART OF THE CORD BETWEEN  
ANY METAL PIECES.  
Fig. 1  
6
 
ASSEMBLY INSTRUCTIONS cont.  
5. To prevent damage during shipping, the Verilux bulb is surrounded  
by protective padding. Carefully remove and dispose of the  
protective padding. Check to ensure that the bulb is fully seated  
and has not come loose from the socket during shipping. There  
should be no gap between the bulb and socket.  
6. Plug lamp into outlet and turn on. If bulb does not illuminate  
instantly, please refer to the troubleshooting section of this manual.  
7
 
BULB REPLACEMENT INSTRUCTIONS  
Removal  
1. Unplug lamp from power source.  
C
2. Firmly hold bulb base (B) and pull  
bulb (C) from the socket (A) in  
an outward motion.  
B
A
Installation  
1. Unplug lamp from power source.  
C
2. Firmly hold base (B) and push bulb  
(C) into the socket (A).  
3. Be sure bulb is firmly seated in the  
socket (see below) and snapped  
into the metal bulb clip (D).  
B
A
YES  
NO  
D
Notice  
large gap  
No  
gap  
Correctly seated bulb  
Incorrectly seated bulb  
CAUTION: ALWAYS UNPLUG LAMP BEFORE PERFORMING BULB  
REPLACEMENT OR INSTALLATION.  
8
 
TROUBLESHOOTING  
Before requesting service on your Planet Light® lamp, please read  
the following:  
• Make sure all power connectors, cords and plugs are inserted fully  
and securely.  
• Be sure the bulb is securely seated into the socket. (See page 8)  
• Make sure there is power to the wall outlet or try another outlet.  
CAUTION: DISCONNECT LAMP BEFORE PERFORMING  
ALIGNMENT ACTIVITY. Problem with aligning screw holes? Always  
start with the base and work your way up the shaft and attach the  
head last. Place your foot on the base of the lamp on the floor. While  
holding the shaft with your hand, gently rock the unit back and forth.  
Shaft should ease into socket and screw holes will align.  
Be sure the bulb is securely seated into the socket, repeat the bulb  
installation process. CAUTION: DISCONNECT LAMP FROM OUTLET  
PRIOR TO REPEATING THE BULB INSTALLATION PROCESS.  
9
 
CARE & CLEANING  
Your lamp is made from high quality materials that will last for many  
years with minimum care. You may want to periodically clean the lamp,  
using a mild non-abrasive cleaner and soft cloth. When cleaning, make  
sure you have turned off and unplugged the unit, and allowed sufficient  
time for the unit to cool. All liquid should be properly wiped away and  
dried prior to restoring power.  
CAUTION: DO NOT USE SOLVENTS OR CLEANERS CONTAINING  
ABRASIVES, OR AMMONIA BASED CLEANERS  
WARNING: All moisture should be properly wiped away and dried prior  
to restoring power.  
10  
 
One Year Limited Warranty  
ATTENTION! ONCE OPENED, PLEASE DO NOT RETURN THIS PRODUCT TO THE  
STORE WHERE IT WAS PURCHASED FOR REPAIR OR REPLACEMENT!  
Customer Service Department at 802-496-3101 during normal business hours.  
This limited warranty is provided by: Verilux®, Inc., 340 Mad River Park, Waitsfield, VT 05673  
Verilux warrants this product to be free from defects in material and workmanship for a  
period of one year from the date of the original retail purchase from Verilux or an authorized  
Verilux distributor. Proof of purchase is required for all warranty claims. During the  
limited warranty period, Verilux, Inc. will, at its option, repair or replace defective parts of  
this product, at no charge to the customer, subject to the following limitations: This limited  
warranty does not include any postage, freight, handling, insurance or delivery fees. This  
warranty does not cover damage, defect or failure caused by or resulting from accident,  
external destruction, alteration, modification, abuse, misuse or misapplication of this  
product.  
This warranty does not cover damage to the product resulting from return shipping or  
handling. The use of shipping insurance is recommended to help protect your product.  
Return Authorization is required for all returns. To obtain a Return Authorization, please  
contact the Verilux Customer Service Department at 802-496-3101.  
If, during the first year of ownership, this product fails to operate properly, it should be  
customer service representative at 802-496-3101.  
Note: Verilux recommends using a quality surge suppressor on all electronics equipment.  
Voltage variations and spikes can damage electronic components in any system. A quality  
suppressor can eliminate the vast majority of failures attributed to surges and may be  
purchased at electronics stores.  
Due to ongoing improvements, actual product may have slight variations from the product described in this manual.  
11  
 
Printed in China for Verilux, Inc.  
© Copyright 2010 Verilux, Inc. All rights reserved.  
PL04-MAN-Rev9  
 

Teac Computer Drive CD 224E R User Manual
Teac Stereo Amplifier A H300mkIII User Manual
Tektronix Welding System 071 0590 00 User Manual
Telex Intercom System BTR 24 TR 24 User Manual
Texas Memory Systems Power Supply 320 User Manual
Toastmaster Coffeemaker TMCMRETB User Manual
Tote Vision Computer Monitor LCD 560L User Manual
Uniden Two Way Radio UHO45XR User Manual
Uniden Weather Radio GMR645 2CK User Manual
Unisar Baby Monitor TV872 User Manual