TechniSat Switch 11 20K User Manual

GigaSwitch 11/20G  
GigaSwitch 11/20K  
Installation Manual and User  
Instructions  
 
2 Safety Hints  
For your own protection, you should read the safety hints carefully before installing the  
GigaSwitch multiswitch. The manufacturer accepts no responsibility for damage caused by  
non-observance of the safety hints, or by inappropriate handling.  
>
>
>
The components must be mounted in dry rooms on flat, non-flammable surfaces.  
Air circulation slots on the components must permit unimpeded circulation.  
The installation must be carried out while the unit is not connected to the power  
mains.  
>
>
The multiswitch must be connected to ground (earthed).  
The antenna installation must comply with local regulations relating to lightning pro-  
tection.  
>
The relevant EU standards as well as VDE or national regulations relating to electrical  
safety must be observed.  
>
>
>
National regulations relating to broadcast reception equipment must be observed.  
Never open the unit cover, as you may be subject to an electrical shock!!!  
If it becomes necessary to open the unit, this should only be carried out by trained  
personnel.  
In the following cases, you should disconnect the unit from the power mains, and call an  
expert/trained personnel:  
>
When the unit has been subject to extreme humidity, or when liquid has entered the  
unit;  
>
>
When the unit malfunctions;  
If the unit shows severe external damage.  
3 Introducing the components  
3.1 GigaSwitch 11/20G (Part No. 0000/3229)  
The GigaSwitch 11/20G is the basic unit in the multiswitch range. The GigaSwitch 11/20G  
provides distribution of the Intermediate Frequency signal to 20 participants, including provi-  
sion of power to the LNBs. In larger installations it also provides the power for the cascade  
multiswitch GigaSwitch 11/20K, for the distributor 9V and for the intermediate amplifier 9Z.  
When installing a cascade system of several components, please ensure that the maximum  
power voltage is not exceeded (see technical specifications).  
3.2 GigaSwitch 11/20K (Part No. 0000/3228)  
The GigaSwitch 11/20K is the cascade unit in the multiswitch range. This unit receives its  
power supply from the basic unit GigaSwitch 11/20G. The GigaSwitch 11/20K unit can thus  
only be used in conjunction with the basic unit. The GigaSwitch 11/20K is inserted between  
the LNBs and the basic unit, with each additional 11/20K unit providing connections for 20  
participants.  
The function of the cascade is to distribute the eight polarisation planes as well as the terre-  
strial signal further along the main connection, and to provide up to 20 participants with inde-  
pendent access to the selected band.  
3
 
3.3 Intermediate Amplifier 9Z (Part No. 000/3231)  
The intermediate amplifier 9z has been designed to compensate for the damping effect of  
25m of multimedia cable, or of 40m of CoaxSat 2150 cable, when used to transmit satellite  
signals. The amplification of terrestrial signals can be adjusted.  
3.4 Distributor 9V  
This is used to achieve a three-way split of main-line connections, while providing a high  
degree of insulation.  
A cascade switch can be connected directly to the lower outputs. The outputs at the front  
can be used to feed a further 2 cascade units, using up to 20m of multimedia cable.  
One or more distributors can thus be used to assemble fairly large installations.  
>
Where the damping of the main line connection is less than 5 dB (at 2150 MHz), no  
intermediate amplifier is required. The intermediate amplifier 9Z is only required  
where higher damping levels are present.  
4 Settings  
4.1 Switchable outputs for each party, 22 kHz or DiSEqC control  
On the side panels of the unit, above each of the uppermost participant output connections  
you will find a switch with which you may set the reaction of the specific output connector  
with regard to 22 kHz or DiSEqC control. These switches relate exclusively to parties 1 and  
2, as well as to parties 11 and 12. They are provided for receivers that do not provide a  
DiSEqC control facility. For such receivers you must select individually the inputs you wish to  
address with the 22 kHz control.  
a) Position A/B  
If the switch is in this position, the Low Band of Position A will be received without the 22  
kHz control signal, and the Low Band of Position B will be received with the aid of the 22  
kHz control signal.  
b) Band Low/High  
If the switch is in this position, the Low Band of Position A will be received without the 22  
kHz control signal, and the High Band of Position B will be received with the aid of the 22  
kHz control signal.  
22kHz schalten  
Position A/B  
Band Low/High  
< Abzweig 2  
The switches are preset to Position A/B at the factory so that receivers which do not have  
4
 
DiSEqC control functions can utilise the 22KHz control signal to switch to the Low Band set-  
ting of Eutelsat 13°. All other outputs are fixed in terms of their switching position.  
The setting of this switch is irrelevant for and not applicable to DiSEqC-  
compatible receivers.  
4.2 Setting of terrestrial Inputs  
Terrestrial signals can be fed into the system in separate bands, or as a broad band signal.  
Use the switch provided to set the required function:  
a) Switch in up position  
Separate inputs for VHF, UHF and FM are activated.  
b) Switch in down position  
The VHF and UHF inputs are deactivated, and should be terminated with 75 Ohm resistors.  
The broad band signal is fed into the system via the FM (UKW) connector.  
VHF  
UHF  
UKW  
/
/
Breitband  
The distribution system is designed to cope with the damping effect of cable up to about 20  
dB (between LNBs and antenna connector) at 2150 MHz. An active diagonal plane compen-  
sation is implemented in order to compensate for cable damping in the satellite range. The  
high level of decoupling of the satellite signals means that damping compensators in the  
main line connections are not required. The required level of damping can be achieved by  
varying the cable type, dependent on the cable length.  
The input level should be at 75 dBµV  
It is possible to configure the terrestrial frequency range with 42 channels in accordance with  
CENELEC regulations. Likewise, due to the carefully designed low-damping system for ter-  
restrial reception with diagonal compensation there will be no problem in future to accommo-  
date DVB-T or DVB-C (terrestrial or cable-fed digital television).  
5 Installation  
5.1 General  
>
>
We recommend that the star-form distribution should originate in the attic, or near the  
centre of the house/building.  
Should the distribution originate in the cellar/basement, we recommend you fit an inte-  
rim amplifier Type 9Z between the basic unit multiswitch and the LNBs.  
Please ensure that the levels of the various satellite systems are approximately equal.  
We recommend, particularly with relatively large installations, that you check all  
cables for short circuiting before fitting contacts/connectors, as it will take much longer  
to search for faults at a later stage.  
>
>
>
Ensure that main connections are not mixed up in any way. You may find it easier to  
make the connections in the distribution system using multi-coloured cable.  
5.2 Selecting an external unit  
>
Ensure that your satellite dish is of adequate size for local conditions. We recommend  
a minimum diameter of 85 cm, and of 1m in the eastern regions of Germany. This  
means that satellite reception will generate a picture with a signal-to-noise ratio of 48  
dB.  
5
 
5.3 LNBs  
>
>
You may choose quattro, dual output or twin LNBs, but not universal twin types.  
Use only high-quality LNBs from reputable manufacturers, such as TechniSat Part.  
No. 0000/8880, providing either linear or diagonal frequency compensation. The out-  
put level should be >75 dBµV.  
>
The LNBs receive their mains power supply via the basic unit GigaSwitch 11/20G.  
Please note the maximum power supply as per the technical specifications.  
5.4 Cables  
>
>
We recommend that you use crimp-type connectors only!  
We recommend CoaxSat 2150 cable for your connections leading to the LNBs. If the  
circumstances within the house/building permit, this type of cable should also be used  
for the connections to the individual participants.  
>
For systems distributing to more than 40 participants we recommend the use of multi-  
media cable for the main line connections (1 x 4-strand, 1 x 5-strand).  
Cables must be insulated as follows:  
>
Damping (dB/x/metre) of suitable cable types  
Type  
At MHz  
CoaxSat 2150  
40 300 860 2150 40 300 860  
Mini Coax  
Multimedia 4 u. 5  
2150 40 300 860 2150  
10m  
20m  
30m  
40m  
50m  
60m  
70m  
0.3  
0.6  
0.9  
1.2  
1.5  
1.8  
2.1  
1
2
3
4
5
6
7
1.8  
3.6  
5.4  
7.2  
9
3
6
0.5 1.5 2.5  
4.2 0.7 1.7  
8.4 1.4 3.4  
12.6 2.1 5.1  
16.8  
3
5
9
4.9  
8.4  
14.7  
1
3
5
9 1.5 4.5 7.4  
12 2 10  
15 2.5 7.5 12.5  
18  
21  
6
21  
10.8  
12.6  
5.5 Selecting the antenna connectors  
The individual participants are connected by means of antenna connectors, e.g. types SV  
500, SVT 500. This allows terrestrial programmes to be received without any need to change  
the connectors. At the same time, this type of connector also protects the receiver from faults  
occurring outside the bandwidth.  
Output levels of a SV 500 antenna connector:  
Damping of connector  
(dB)  
Level (dBµV)  
recommended maximal  
minimal  
47  
50  
55  
55  
Sat-bands  
UKW  
58  
63  
63  
63  
79  
70  
70  
70  
2
5
4
VHF  
UHF  
6
 
6 Installation Hints  
>
>
>
We recommend a star-form distribution originating in the attic, or near the centre of  
the house/building.  
Please ensure that the levels of the various satellite signals fed into the system are  
approximately equal in strength.  
The outputs for participants 5…10 and 16…20 supply a higher output level in the  
satellite band. You should use these outputs to connect participants with longer cable  
connections.  
>
Checking all cable connections before connectors are fitted (to identify short circuits)  
saves a lot of time possibly searching for faults once everything has been installed.  
Ensure that connections coming from the LNB are not mixed up.  
If you are installing a fairly large set-up, draw up an input level diagram before you  
start.  
>
>
>
>
>
Make your calculations based on the amplification values given in the technical speci-  
fications as well as the appropriate cable damping factors as set out above.  
Try to use single uninterrupted lengths of coaxial cable to make your connections. F-  
connector plugs may cause interference of DVB signals.  
Ensure the covers of the F-connectors are secured moderately tight. You should use  
the adjustable spanner Art. No. 0000/3407.  
>
>
Do not use snap-tight F-connector covers!  
Some older models of LNB require an operating current of 12 V. In this case, be sure  
to switch on the voltage limiter provided by the LNB manufacturer between the LNB  
and the input of the multiswitch.  
Distribution of terrestrial programmes:  
>
Ensure that output levels are approximately equal (recommended 75 dBµV/Maximal  
90dBµV)  
>
When receiving several terrestrial channels from the same direction, you can utilise  
one or more interference filters, eg. TSF 2169/2, Part. No. 000/6042 in order to adjust  
signal levels. You will have to know the band allocation, and use an antenna (signal  
strength) measuring instrument in order to set the levels of the interference filters in  
such a way that weaker signals are not lost against the background noise.  
If additional diagonal compensation is required, TechniSat manufactures a BK com-  
pensator, Part No. 0000/3166.  
>
>
It may be beneficial to insert a damping unit each at the FM input if FM or cable sig-  
nals are being fed into the system.  
>
>
Signal strengths of < 55 dBµV are not suitable for distribution systems.  
Where input signals are weak, a low-noise pre-amplifier with high damping should be  
employed.  
>
>
If a 11/20K unit is cascaded directly with a 11/20G basic unit it may be necessary,  
depending on input levels, to insert a damping controller in the terrestrial signal path  
between the two units.  
If it is your intention to supply a number of participants with only terrestrial signals,  
you should distribute only the combined terrestrial input signal. If necessary, a pre-  
amplifier can be included in the circuit before the signal reaches the multiswitch.  
7
 
7 Installation examples  
Installation for up to 20 participants  
Distribution from attic;  
Input Levels  
60  
60  
Output levels at connec-  
tor from unit  
Recommended  
8
 
9
 
10  
 
8 Troubleshooting guide  
Problem  
Possible cause  
Solution  
No reception on any  
polarisation plane  
Short circuit in LNB  
Remove each cable individually, until  
green LED remains on.  
> green LED blinking  
Fix short circuit cable section  
No reception on any  
polarisation plane  
> green LED on  
Antenna adjustment faulty  
Check signal incoming to LNB.  
Check that correct LOF setting is set  
at receiver.  
Check power supply of LNB at 11/20.  
No reception or wrong LNB connections mixed up, Check allocation of cables and  
programme at specific or core cable too short  
polarisation planes  
connectors.  
Check the LNB connection directly.  
Note however that power is not  
supplied to all outputs of quatro  
LNBs  
Individual participant  
outputs not working  
LNB voltage and/or  
switching criteria of the  
receiver incorrect  
See what happens if the receiver is  
connected to a different participant`s  
output. Be sure to switch on the  
receiver after connecting it, in order  
to reset switching criteria.  
Check LNB voltage and switching  
criteria with a testing unit.  
Wavy lines in terrestrial Input level too high  
TV picture  
See technical specifications  
Your equipment bears the CE-logo and complies with all relevant EU regulations!  
Subject to change and printing errors. Last revised 10/00.  
TechniSat is a registered trademark of  
TechniSat Digital GmbH  
P.O. Box 560  
D-54541 Daun Germany  
460/99  
11  
 
12  
 

Top Innovations Iron SF 435W User Manual
Tripp Lite Surge Protector Data Shield User Manual
Tripp Lite Surge Protector ISOBAR4ULTRA User Manual
Troy Bilt Trimmer TB25ET User Manual
Turbo Air Beverage Dispenser TBB 1SB User Manual
Turbosound Portable Speaker TQ 440 User Manual
VTech Cordless Telephone QW2432 User Manual
Walker Indoor Furnishings W44CFDBL User Manual
Watlow Electric Electric Heater 316 42 15 1 User Manual
Weed Eater Blower 545186783 User Manual